Table of Contents Add to my manuals Add. Page 72 Theory of Operation Ver1. Bundle arm control The bundle arm motor M10 rotates in the reverse direction when the main body start signal  turns ON and moves the bundle arm to the appropriate position in accordance with the paper size. Image Processing Theory of Operation Ver1. In the punching mode, the motor M1 stops temporarily after the FNS entrance sensor PS4 detects the rear edge of paper.
|Date Added:||24 March 2004|
|File Size:||16.4 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Job partition plate In stacker tray sort mode, the trailing edge of the shift paper is restricted by the job partition plate and the paper is exited onto the stacker tray 20 mm shifted from the non-shift paper. Overlap control 1 Multi letter folding mode control In the multi letter devvelop mode, up to 5 sheets decelop stacked in the right angle conveyance section and conveyed to the folding section.
For more details, or to find out how to disable cookies please follow this link. The laser light can enter your eye, leading to a risk of loss of eyesight.
Page 84 Theory of Oneo Ver1. Control 1 The number of the print paper is iheo or more 32 or more for the saddle stitched paper The trimmer press motor M32 rotates in the reverse direction  when the bundle clip motor starts conveying the paper . After the 2nd folding conveyance sensor PS53 turns ON, the paper is conveyed by a specified number of steps.
The edge detection is performed at four points edges per mark.
These operations are common to all the modes. Bundle arm control The bundle arm motor M10 rotates in the reverse direction when the main body start signal  turns ON and moves the bundle arm to the appropriate position in accordance with the paper size.
Theory of Operation Ve1. Functions 1 Functions Accelerated conveyance To accelerate for the finisher standard line speed.
If an accident has occurred, the distributor who has been notified first must immediately take emergency measures to provide dwvelop to affected persons and to prevent further damage.
Alignment mechanism The alignment is conducted by driving the alignment claws  by the right angle conveyance motor M6  through the belt  and the torque limiter .
Toner, drums and developer kits for Develop Ineo
At this time, the upper surface of the non- shift ddvelop does not come to the same eevelop as the lower edge of the job partition plate and the 1st sheet of the shift paper is in possibility of getting into the lower side of the job partition plate. Bypass gate control The bypass gate only operates for the small size paper A4, B5, and 8 x 11 in the stapling mode.
Registration loop control The FNS conveyance motor M1 turns OFF temporarily to stop conveyance of paper when the specified time has passed since paper exit sensor PS13 detected the leading edge of the paper.
Functions Punching method Stops and punches every paper No.
At this 65000, the shift unit has been dwvelop to the position specified in advance for each paper size. Then, M1 rotates at the same rate as the line speed of the main body while M5 rotates at high speed. Single-sided mode thick-paper mode: Control The bundle registration motor M12 rotates in the reverse direction when the main body start signal turns ON and the registration claws move to the standby position in accordance with the paper size .
The paper exited to the bundle exit tray is conveyed to the front by the bundle exit conveyance belt  and stacked.
Toner cartridge for Develop Ineo +
PK 2 to 3 holes       15kjt2enb Punch motor M Groove of the switching cam Eccentric cam Projection of the punch blade Slide link  Eevelop of the switching cam Switching cam Page 30 Theory of Operation Ver1.
Straight mode fdtoc Paper through from the PI Paper through from the main body paper exit Double-sided mode The first sheet of original is conveyed in the same manner as in single-sided mode.
If 6500 leakage occurs in an ungrounded product, you may suffer electric shock while operating the product. Bundle exit paper full control The bundle tray paper full sensor PS61  detects the bundle exit paper full.
Download Centre – DEVELOP | Europe
Image Processing Theory of Operation Ver1. The roller  attached to the arm  is pushed up and the clincher is contacted with the stapler when M20 rotates the eccentric cam . Stacker entrance transfer control 1 Stapling mode the paper size is not A4, B5, or 8 x 11, without the bypassing operation Transmitting the FNS signal from the main body , the stacker entrance motor M13 turns ON and rotates in high speed.
For this reason, when the switching cam is rotated clockwise, the punching blade is driven downward and when the cam is rotated counterclockwise, the punching blade is not driven.
At the time, it also moves the bundle exit conveyance belt drive shaft  for the bundle exit conveyance belt  and . M24 stops while holding the bundle press stage in slant- ing position when the bundle press stage up down limit sensor PS45 turns ON .